The Home of DIY Handyman Repairs
The Home of DIY Handyman: How to Install a Handrail, Balusters, Newel Post
Handyman Home Repairs
STEP 4    Cut and install the shoerail and balusters

The ends of the shoerail are cut at the same angle as the
handrail. The piece is measured, cit and placed on the cap. In
our example it was glued on the backside and installed with
2" wood screws spaced at about 18" apart.

The balusters have a top and a bottom. Gather the balusters
and determine which end is up, usually it is the tapered end.  
The angle of the cut is determined by holding a baluster
plumb and level to the rail and cap and simply marking the
line with a pencil. The cut is made a bit longer than the pencil
mark and can be adjusted for a precision fit. It is important to
cut both ends mostly equal and allow for a balanced look-
instead of lopping off a big chunk at the bottom of the post
and a small cut at the top, or vice versa.

With a properly cut baluster the distance is measured equally
and the  balusters spaced on the division marks. For 5
balusters there are six spaced and 5 divisions. The space is
the area between the balusters where the fillets will be

The balusters are placed in the opening between the cap and
the handrail. The fillets are cut in between the balusters. The
balusters can be installed with glue as well as the fillets. In
our example the fillets were secured with white glue and 1"
"A handrail and balusters is a rewarding project for any diy home handyman.
Your skills with hand tools and a dose of patience will prevail. This is finished
carpentry and one of the tricks to a fine job is to have good tools. There are no
shortcuts when it comes to finished woodwork."
STEP 3   Cut and install the handrail.

The ends of the handrail are cut at the same angle as the cap,
in our example about 40 degrees. Another method is to hold
the uncut handrail alongside the stair treads and mark the
piece at the wall. When cutting allow for a margin of error by
making the cut a 1/4" larger or so. Then, hold up the piece on
the wall and check the angle and re-cut accordingly. The same
method is applied on the end of the newel post.

At the newel post end  we drill from the bottom of the rail into
the post. The handrail was secured with white glue and a 3/8"
x 2" anchor bolt and washer. The angle of the bore was made
at a slight angle (20 degrees or so) up into the post. The hole
will be covered by the fillets.

At the wall the rail is first attached to the rosette. The rosette is
aligned on the cut end and holes are pre-drilled to allow for
the attachment with a single wood screw and white glue. The
screw is inserted on the backside or the rosette into the
NOTE: Do not make the mistake of drilling the screw
perpendicular to the rosette, otherwise it may pop out on the
top of the handrail. Hold the drill at the approximate angle of
the direction of the handrail.

Once the rosette is in place the rosette is nailed into the solid
surface at the wall. The attachment can be made with screws
or nails and a bit of construction adhesive on the backside of
the rosette. If screws are used allow for the hole to be filled
with a wood plug to conceal the screw heads. Nail holes are
filled with any sort of putty.
Handyman Home Improvement Remodeling Service Areas of Ohio: Counties of Cuyahoga, Geauga, Portage, and Summit. Canton, Chagrin Falls, Copley, Cuyahoga Falls,
Doylestown, Ellet, Fairlawn, Garrettsville, Gates Mills, Green, Hiram, Hudson, Hunting Valley,  Jackson Twp., Kent, Lakemore,
Macedonia, Mantua, Massilon, Medina, Moreland
Strongsville,  Streetsboro, Tallmadge, Twinsburg
adhesive, glue and screws or nails. The fasteners are installed
near the center lengthwise of the wood to be concealed by the

STEP 2    Install the newel post
The newel post is the "anchor" of the handrail. It is the piece
that will take the brunt of the use of the stairs. For this reason it
should be installed plumb and secure. In this example we first
with the paddle bit (as shown). The paddles bit must be sharp
for a clean cut. The other type of bit to use could be a 1/2 - 3/4"
of an inch deep, the deeper the bore the less "meat" available
for the anchor.

The second bore is made with a 1/2" wood bit to allow the shaft
of the bolt to pass through the newel post. The third bore is into
the wall and this is done with a 5/16" bit.  This allows for the
bolt to grab yet is not too tight to split the wood to which it is
attached. We use carpenters glue, sometimes known as white
glue to the backside of the post. We also take a caulk gun with
heavy duty construction adhesive (PL 400 or equivalent) and
squirt it into the 5/16" hole at the wall side. When the bolt is
inserted into the final assembly the construction adhesive will
be drawn into the shaft and eventually become hard and

The newel post must be plumb and level before making the
bore into the wall. In our example a few shims were used to get
everything plumb and level. Once we get the shims in place
they are removed and coated with white glue and re-inserted.
When dry it will provide additional strength to this critical area.

While bolting the pieces together the 4-foot level is used to
lever the post in all directions. Once the post is lever the bolts
are tightened. A few shims are placed below the post to add
additional support. Once the post is secure the shims are cut
where exposed but left in place below the post.

STEP 1    Install the stringer cap

The wall next to the stairs can be referred to as a stringer wall.
The stringers are the sides of a set of stairs to which the treads
and risers attach. In this example the stringers are referred to
as "closed". The cap in our project is 1 x 8 red oak. We
measure the width of the stringer wall and add 3/4" to each side
to allow for a proper overhang. The red oak is cut "ripped"
lengthwise to the proper width. The overhang is to allow for a
trim piece on the underside of the cap. The ends are cut at
angles. The angle is about 40 degrees. In order to find the
precise angle we used a few pieces of scrap wood, made a few
cuts and adjusted the angle of the miter saw as needed.
Another method is to use an adjustable square.

The cap is installed with any combination of construction
1.The Handrail. Handrails come in many shapes, sizes and   wood
species. The one pictured here is made  of red oak. The underside of
the handrail is notched to receive the balusters, the notch  makes this
a plowed handrail.

2. The Shoerail. This is the piece of oak bottom  channel that  will
attach to the 1 x 8 oak plank.  It is notched or "plowed" to receive the
bottom of the  balusters.
3. The Newel Post stands about 42" tall (seen below).

4. Balusters. The vertical pieces square on the ends and rounded in
the center. In this diagram there are 5 balusters.

5. Rail Bolt Kit. A rail bolt kit consists of a lag bolt of 4-5" in length, a
washer and a wood plug or cap. This kit is used to attach the newel
post to the bottom of the stairs.

6. Handrail and shoe rail fillets. The piece used to fill in the notched
(plowed)  sections of the of the handrail and shoerail.